Plastic Injection Molding Factory.We are advanced China Plastic Injection Molding manufacturers. Our Plastic Injection Molding manufacturing methods are extremely accurate and fast. They can provide unlimited rapid prototype plastic injection molding capabilities for a wide variety of high-volume products. The method is also used for low volume, high-quality plastic parts for everything from toy cars to giant television screens. Rapid prototyping is the process of designing and creating a new product or component using plastic injection molds. It is a critical process because it helps identify new product characteristics by testing them over again before a product goes to production.Plastic injection molds allow designers and engineers to create detailed models from digital designs that can then be brought to life into a physical product. This kind of design sharing provides a tremendous advantage for companies trying to reduce product development costs.
The Finishing Option For Injection Molding
Advantages Of Plastic Injection Molding From RongNa
Injection Molding,Polycarbonate Injection Molding,Custom Injection Molding,Thermoplastic Injection Molding Ningbo Rongna Technology Co.,Ltd , https://www.machiningcustom.com
When running dosing system, pay attention to the following points:
A. Dosing pressure B. Stroke frequency C. Suction height D. Altitude E. Corrosive chemicals When metering pump outlet at atmospheric pressure, is there any way to improve the pump double counting accuracy?
Installing the valve spring at the metering pump discharge valve improves repeat metering accuracy, but the most effective improvement is the installation of a backpressure valve at the end of the line.
How to adjust the back pressure valve?
1. Never exceed the maximum working pressure of the metering pump.
2. When the dosing pump has pressure on the suction side, the pressure on the discharge side of the pump must be at least 1 bar higher than the pressure on the suction side.
How to choose the right pulse damper volume?
By multiplying the metering capacity (ml) per stroke of the metering pump (ml) by 26, the minimum volume (ml) of the pulsation dampener required to reduce the 90% pulsation can be obtained.
How to set the pressure relief valve?
The pressure of the safety valve can be adjusted within the range of the rated working pressure of the metering pump. It is not allowed to exceed the maximum working pressure of the metering pump. The safety valve is designed to prevent over-pressurization of the metering pump. For example, if the maximum working pressure of the metering pump is 3 bar, the relief valve pressure should be set at 3 bar, or lower to ensure proper operation of the metering pump. Overpressure is one of the major causes of dosing pump damage.
If the delivery of liquid is not water, how to calculate the suction height?
Divide the metering pump's nominal aspiration height by the specific gravity of the metering liquid.
Under what circumstances with self-irrigation suction?
Self-priming aspiration can be applied if:
1.Measurement of liquid volatile;
2. Measuring the proportion of liquid larger;
3. When higher stroke frequency is required;
4. Metering pump work in high altitude areas;
5. In the field of application requires a larger tank, and rely on the self-priming pump is not feasible.
Could you give me some advice on pump head selection? What are some common problems with chemical pump head / seal corrosion and should I avoid?
The usual problem when it comes to metering pump heads is the presence of acid, chlorine, fluoride and hydrogen peroxide. Due to the different drug concentration and operating temperature, it is difficult to determine the specific pump head material. When measuring fluoride, we recommend using a Viton® sealed PVC pump head. For most chlorination applications, it is best to use an EPDM sealed NP (plexiglass) pump head. For the hydrogen peroxide mixture can only be measured PTFE PTFE sealed PTFE pump head or stainless steel pump head. Concentrated hydrochloric acid is usually measured Viton? Sealed plexiglass pump head. Concentrated sulfuric acid can be selected PTFE sealed PTFE pump head. Manufacturers of chemicals may give advice or consult ProMinent ™ chemical preservative charts to determine the compatibility of chemicals with contact materials.
When measuring the liquid in the pump head, which factors must be considered?
The main factors to be considered are the viscosity, specific gravity, vapor pressure and temperature of the liquid.
Many rapid injection molding tools include tools that are designed to assist the manufacturer with their overall production efforts. These tools can offer you a number of additional services including computer software designed to help you streamline your production efforts and increase your profitability. By streamlining your efforts, you can expect to see a significant increase in your production rate and efficiency.
RongNa offer OEM/ODM custom rapid prototype plastic injection tooling which can help you reduce the time necessary to create new parts and can save you valuable money on material costs.
.Matte
.polished,
.sprayed,
.screen printing,
.pad printing,
.thermal transfer,
.water transfer,
.laser engraving,
.electrophoresis (water plating),
.vacuum coating,
.biting (etching, skin texture) for plastic molds
According to the customer's requirement to choose the Rapid tooling or the common mold,multi - cavities to save costs. Dozens of material and finishing options available.
analysis before quoting, also will suggest the better design way.
send the mold desgin for checking before tooling make.
Procuring parts on demand, without MOQ.
All products are inspected before shipment.
Metering pump in use to deal with problems
When running dosing system should pay attention to what important matters?